I got a cheap Nest E thermostat on eBay from a charity shop seller. It cost me like £15.

Replaced my dumb one with it, then hooked it into HA and made a sensor from all my motion sensors and door sensors which all have temperature gauges in them.

Conglomerated those sensors into one that tracks the average (making sure to only have so many per floor so as not to skew the data to one part of the house) then made a sensor called “Is it cold enough to have the Heating on?” which acts as a simple switch with a lower and upper limit.

Now my heating only comes on when I need it to based off the temperature of the whole house instead of that one place the dumb thermostat was based.

The display unit for it died after less than a year, replaced that for another £20 on eBay and synced the new unit to the Thermostat on the wall.

So for less than £50 and some smarts I’ve upgraded my heating, and saved money on the bills (since it only comes on when we need it to rather than based on the temperature of one location).

I’m not particularly recommending Nest since I have no experience with other manufacturers, but I managed to do it all on the cheap and I’m quite pleased with the results

2 things, one of which has already been said

Get an SSD and a usb cable for it. Boot off that. Be aware that not all cables are the same (have a Google for usb 3 SSD cables for home assistant before you buy one). There’s a little song and dance you have to do to boot off ext SSD but it’s not hard and doesn’t take long (Google).

That combo will eliminate the SD card issues in the future. But you also need to look into the Google Drive backup add-on. Get that for when shit goes down.

With those two things you should be all set and eliminate this ever happening again. If it does you have a backup.

I’ll be honest and say that most of my self hosted music collection was pirated or ripped from CD like 20 years ago. I put it all on an iPod back then.

I found the iPod gathering dust in a drawer when I finally got a car with a usb jack a couple years ago (yeah I’m not exactly laden with bags of cash over here) and recently pulled all that music back onto my newly set up media server.

I have a Spotify family account I’m trying to phase out with resistance from the children.

To support artists I go and see them when they tour and buy a ludicrously expensive t-shirt

Yeah I know, I use Gluetun now, I was just answering OPs question.

I ran a Linux VM and just had Mullvad app installed and always on, and that was all I needed

Yes

I think you should have a thin sheet of steel kept in your car or somewhere safe, so you can just use that like a locksmith.

Plex was easy enough to set up. I use plexamp on my phone but can access the Plex server via a browser, which includes my music

Yeah I mean I get it because I was also thinking about self hosting for a long time and had a bunch of questions myself.

The problem is that a lot of the questions were not needed, and a bunch of the other questions I answered myself by just tooling around with the stuff.

Great comment btw, it’s a good idea to have a list of the services you’d like to run, in order of importance z then work through it.

I did that then found ways to combine a bunch of services, to the point where I had multiple stand alone VMs that are now just one for Home Assistant and second for Plex and Docker

I see a lot of posts like this and it’s always people overthinking something they haven’t tried to do yet.

So my advice is to just do it.

You may lose everything at some point in the future, Satan knows I have a few times, but because you’ve actually done it, you can do it again.

Now, because you’re just thinking about doing it, it seems like a massive deal because you’ve not gone out and done it yet.

As for recommendations, I use a Proxmox VM with Debian and Docker. My Proxmox does backups, but my Docker compose is also a text document on my PC so I can recreate it all from scratch from that. I also have an idea what I did when I was learning how to do it, and have retained a good bit of that info so I could probably do it without either the backups or the Docker Compose, it would just take longer.

Just do it

Commenting just to add “nofail” to the fstab.

I didn’t do this in Proxmox and then the drive stopped working and so did Proxmox. As a noob I ended up starting fresh and losing lots.

After adding nofail the services start up, just without the NAS attached. Without nofail it just doesn’t boot.

Nofail for the win

I’m running Proxmox on a mini PC. I have a Debian VM for streaming and a Home Assistant VM.

Runs like a dream

Well I guess it’s racist to call them bell ends now then, fucking bell ends

Just Google “Booting a pi from an SSD” and follow the steps

I can’t remember the steps (they were simple though) but when my Home Assistant raspi SD card died, I bought a 128gb SSD from AliExpress and a usb-sata cable.

I then did something to the pi that meant it can boot from the SSD, and flashed the SSD using Balenetcher or RUFUS or whatever (same program I was using to flash my SD cards basically).

Then it was just a case of plugging in and turning it on.

Runs exactly the same as with an SD card with less dying because SD cards aren’t meant for a lot of read/write but SSDs do.

In a community without a lot of content, complaining about added content is a bit rich, but some people are just dicks, it’s a fact of life.

Scroll on with your day

We just take a tote bag full. If anyone says anything they have just lost our custom. Can’t stop people smuggling snacks when nobody goes

It does. I use Mosquito but I believe HA has a built in one too. Mosquito was easy enough to set up though.

Honestly MQTT is like the nervous system of my HA setup. I started using it with Tasmota when I Tasmotised all my cheap WiFi bulbs, then opted for Zigbee2mqtt for my ZigBee setup.

But I also have things like my bedside clock (an old phone running WallPanel), my doorway tablet (a Nexus 7 running Fully Kiosk Browser), my PC and even my alarm clock app on my phone, all running through MQTT.

I even had Tasker on my phone communicating with HA via MQTT before I gave up on that. It’s really useful

Just set up MQTT in home Assistant, why not?